The Australian Water Balance Model (AWBM) is a catchment water balance model that relates daily rainfall and evapotranspiration to runoff, and calculates losses from rainfall for flood hydrograph modelling. The model contains five stores; three surface stores to simulate partial areas of runoff, a base flow store and a surface runoff routing store.
Scale
AWBM operates at the functional unit scale and at a daily time-step.
Principal developer
Cooperative Research Centre for Catchment Hydrology. The original model was developed by Dr Walter Boughton.
Scientific provenance
AWBM has been applied in many Australian catchments by the original author (Boughton) and by several other hydrologists. The extent of its use outside Australia is unknown but it is not expected to have been widely applied outside of Australia. There is nothing particularly unique to Australia in the conceptual structure of AWBM but it would require calibration and testing to catchments outside of Australia to confirm its suitability.
Version
Source v2.10
Note AWBM cannot be used at sub-daily time-steps in Source.
Rainfall Runoff Library v1.0.5, June 25, 2004
http://www.toolkit.net.au/Tools/RRL
Dependencies
None.
Availability & conditions
AWBM is automatically installed with Source. AWBM is also available through the Rainfall Runoff Library on eWater Toolkit:
http://www.toolkit.net.au/Tools/RRL
Structure & processes
AWBM uses three surface stores to simulate partial areas of runoff. The water balance of each surface store is calculated independently of the others (Figure 10). The model calculates the moisture balance of each partial area at daily time-steps. At each time-step, rainfall is added to each of the three surface moisture stores and evapotranspiration is subtracted from each store.
Figure 10. Structure of the AWBM rainfall-runoff model
If the value of moisture in the store becomes negative, it is reset to zero, as the evapotranspiration demand is superior to the available moisture. If the value of moisture in the store exceeds the capacity of the store, the moisture in excess of the capacity becomes runoff and the store is reset to the capacity.
The catchment area is divided into 3 subareas, A1, A2 and A3, each representing user defined land use or soil classification as proportions of the area of the catchment. Thus the sum of A1, A2 and A3 must be 1. Only A1 and A2 can be set with A3 being the remaining area proportion, A3=1 - (A1+A2). The default pattern is A1= 0.134, A2= 0.433 and A3= 0. 433. When A1 and/or A2 are changed, A3 will be adjusted to respect the constraint. If the user increases A1 or A2, and A3 cannot compensate, then A1 is reduced to still respect the constraint.
When runoff occurs from any store, part of the runoff becomes recharge of the base flow store if there is base flow in the stream flow. The fraction of the runoff used to recharge the base flow store is BFI x runoff, where BFI is the base flow index, ie the ratio of base flow to total flow in the stream flow. The remainder of the runoff, ie (1.0 - BFI) x runoff, is surface runoff. The base flow store is depleted at the rate of (1.0 - K) x BS where BS is the current moisture in the base flow store and K is the base flow recession constant of the time-step being used (typically daily).
The surface runoff can be routed through a store if required to simulate the delay of surface runoff reaching the outlet of a medium to large catchment. The surface runoff store acts in the same way as the base flow store, and is depleted at the rate of (1.0 - KS) x SS, where SS is the current moisture in the surface runoff store and KS is the surface runoff recession constant of the time-step being used.
Input data
The model requires daily rainfall and evapotranspiration data (ET). The rainfall and ET data sets need to be continuous and overlapping.
Compared to rainfall, evapotranspiration has little influence on the water balance at a daily time scale and thus areal potential evapotranspiration is used (Boughton & Chiew 2003).
Daily rainfall data may be obtained from rain gauges or rainfall represented as a spatial layer, eg rainfall grids, but will need to be converted to a time series record that is spatially representative of the whole catchment. Note that the time that rainfall data is collected may be important. Very often rainfall data is collected in the morning, the usual time is 9am, and may be more representative of the previous day’s rainfall.
Daily PET is an estimate of the spatially averaged areal potential evapotranspiration rate of the catchment being modelled. This estimate is subject to a number of climatic and land use/land cover variables. This may be estimated by applying a crop/land use factor to daily pan data or extracted directly from maps of calculated areal potential evapotranspiration data. |
Selecting stream flow data to use in a river-basin-scale simulation study needs information about the reliability of the data. It is best to use data which are most representative of the stream flow from the catchment. Observed data would normally be selected, except where the data are of poor quality or of unknown reliability. |
Parameters or settings
Table 2
.The relative sensitivity of parameters will vary between catchments but generally the model is most sensitive to the recession constants and base flow index. |
Output data
The model outputs daily surface and base flow. This may be saved in ML/day, m3/s or mm/day.
Configuration
Daily flow data in ML/day, m3/s or mm/day may be required to calibrate the model.
This model requires calibration and validatiion. |
References
.
Bibliography
Boughton, W.J. (2004) The Australian water balance model, Environmental Modelling & Software, vol. 19, pp. 943-956.
Table 2.Model parameters
Parameter | Description | Units | Default | Min | Max |
|---|---|---|---|---|---|
A1 | Partial area of surface store 1 (Proportion of the catchment) | 0.134 | 0.000 | 1.000 | |
A2 | Partial area of surface store 2 (Proportion of the catchment) | 0.433 | 0.000 | 1.000 | |
C1 | Capacity surface store 1 | mm | 7 | 0 | 50 |
C2 | Capacity surface store 2 | mm | 70 | 0 | 200 |
C3 | Capacity surface store 3 | mm | 150 | 0 | 500 |
BFI | Base flow index | 0.350 | 0.000 | 1.000 | |
K | Base flow recession constant (proportion of moisture depth remaining per time-step) | 0.950 | 0.000 | 1.000 | |
KS | Surface flow recession constant | 0.350 | 0.000 | 1.000 |
The relative sensitivity of parameters will vary between catchments but generally the model is most sensitive to the recession constants and base flow index. |
Output data
The model outputs daily surface and base flow. This may be saved in ML/day, m3/s or mm/day.
Configuration
Daily flow data in ML/day, m3/s or mm/day may be required to calibrate the model.
This model requires calibration and validation. |
References
Boughton, W & Chiew, F 2003, Calibrations of the AWBM for use on ungauged catchments, Technical Report 03/15, Cooperative Research Centre for Catchment Hydrology, Canberra.
Bibliography
Boughton, W.J. (2004) The Australian water balance model, Environmental Modelling & Software, vol. 19, pp. 943-956.