This section describes the Source processing tools that are installed by default, accessible via the Tools menu and sub-menus.
| Anchor | ||||
|---|---|---|---|---|
|
The Data calculator (accessed via Tools Data Calculator Tool) can be used to analyse spatial raster data and time series through the use of simple arithmetic operators, or to compare data sets.
| Info | ||
|---|---|---|
| ||
| Note: Use can also drag and drop data to and from the Charting tool. First, choose Draggable from the contextual menu (as shown in Figure 1). Then, drag and drop the raster data or time series to the Charting tool. |
You can use rasters, time series or numbers as operands as follows:
- Drag and drop the raster data or time series into either of the two view controls (raster or time series are displayed in a small window called a View Control (Figure 1), or use a combination of a raster/time series and a number.
- Use the radio buttons to select either the view control or numeric values as left and right operands;
- Click one of the basic operations buttons (addition, subtraction, square root etc). The data calculator displays the operand you selected; and
- Click =, and the result, either raster/time series or numeric, appears in the results area on the right.
| Info | ||
|---|---|---|
| ||
| Note: Time series and raster data need to be in a format compatible with Source. Refer to Data file formats. |
The memory feature of the data calculator allows you to save previous results, either numeric or raster/time-series.
Click Memory to open the memory area. To save a result raster/time series into the memory, click on the 1st or 2nd operand, or result, view control, then drag and drop the contents into your desired memory view control. The label above each view control resides shows the mathematical operation leading to the result stored there. Figure 3 shows the memory area with several stored results.
| Info | ||
|---|---|---|
| ||
| Note: When you close the data calculator, the stored results are not saved. If you want to keep any of the rasters, right-click the raster, and choose Save from the contextual menu. |
Figure 1. Data Calculator with data stored in memory
To save any of the results, right-click any of the view controls, and choose Save from the pop-up menu. You can also drag the contents of any view control into any other view control or graph form anywhere else in Source.
The Stats tab gives a statistical summary of the data sets that have been analysed with the Data Calculator. The Reflected Operations tab provides additional data manipulation operations, such as Merge, find Maximum value or multiply two rasters. It allows you to perform customised operations. You can use a plugin to create these operations, which then appear on the list, and can be performed on various data sets.
Data modification tool
The Data modification tool allows you to edit data inputs depending on conditions that you wish to specify. Choose Tools » Data Modification Tool to open the tool, as shown in Figure 2 and carry out the following steps to change the data inputs:
- Click Open under Data loader, which displays the file name in the box below, along with the file on the right;
- Under Condition builder, click Add to add a condition. The input data, conditional operator and condition value can be accessed by hovering and clicking on the relevant area in the condition builder. A drop-down menu appears;
- Click Name to associate a name with the condition;
- Clear can be used to clear the list of conditions if it gets too long and is no longer required;
- Under Rule Executer, you can specify the output for specific aspects of the input. For example, if the condition reaches a certain value, the result will be 0; and
- Click Execute, and the output will be displayed in Result, which can be saved by clicking Save.
Figure 2. Data modification tool
Data unit converter
As its name suggests, this tool converts units (embedded into data files) from one type to another. It is accessible via Tools Analysis Windows Data Unit Converter (Figure 3).
Figure 3. Data Unit Converter
Use the converter as follows:
- Drag and drop a data file onto the Source data window in the left side panel. If there are units in the data file, they will appear in the units field below the input window;
- Enter the output/target units in the Units field on the right side (under Converted Data). You can either use the default name (copied from the source data file) or enter a new name; and
- Click Convert. To save the converted file, drag it somewhere else in Source that has a Save as function. This is because you cannot right-click the converted data graph and save it.
If there are no units in the input file, you must force the data converter to assume that there are input units by ticking the Override input units checkbox and entering the "assumed" unit under Units. For example, you have a CSV file containing dates and rainfall, but it does not contain any units. You want an output containing metres per day. Assume the input is in mm/day:
- Drop the input file into the Source data window;
- Tick the Override units checkbox;
- Enter mm.day-1 into the Units field;
- In the converted data window, enter the name for the converted data set;
- In the converted data window units field, enter m.day^-1 (metres per day); and
- Click Convert. The converted data should be scaled down.
You can also scale the converted output to your desired units by ticking the Use converting quantity checkbox. Enter a non-zero value into the Value field and click Convert to scale the output by both the value and the difference in magnitude of the units eg 0.5 mm/h converted to m/h with value 3 ends up being 0.0005 m/h. Note that you must specify both the source value and the target units.
Right clicking in the Converted data dialog will reveal a pop-up menu of options. This enables zooming, panning, dragging, formatting and copying a picture of the output graph to the paste buffer.
Graph Control
Choose Tools » Graph Control to open a charting tool window, which can be used to drag data and display it. Refer to Using the Charting Tool for details.
Mapping Analysis window
The mapping analysis window (accessible via displays a map of flows and constituent loads per sub-catchment. The relevant catchment variables must have been recorded in the scenario run to be able to view them in the Map Analysis Window. You can perform the following functions in this window:
- To display flows and loads in each sub-catchment, under Map Details, click to open the Runs drop-down menu. Choose a scenario, then the desired Variable and Statistic values from the respective drop-down menus. Move the mouse cursor over a sub-catchment in the map view. A tool-tip appears near the mouse cursor, indicating the variable amount for that sub-catchment per year (Figure 4);
- Flows are reported in ML/d and constituent loads in kg/d;
- You can calculate the difference between two scenario runs by enabling the Subtract checkbox. Carry out the same steps outlined above for the mapping analysis window; and
- Display results per unit area by enabling the Divide by Area checkbox. Flow depth is reported in m/s and constituent load in t/km2/y.
Figure 4. Mapping form with tool-tip showing TSS
Regression tests
Regression tests ensure the following:
- Changes (such as bug fixes) on in Source do not introduce additional problems;
- Old projects are compatible with future versions of Source; and
- Correct results are not inadvertently changed due to altered because of software changes.
A detailed description on working with regression tests can be found here.
Running regression tests locally
There are three sub-menus under Tools » Regression tests that allow you to create and run regressions tests locally. The first step is to set up the baseline project for the regression test project and build the test using the Scenario test builder.
Create/Edit Regression Test Description file (.xml)
This allows you to document information about the test files that were saved in the scenario test builder. It tells you what functionality each file is testing and is saved in XML format.
Choose Tools » Regression Tests » Create/Edit Regression Test Description file (.xml) to open the Add Regression Test Project dialog (Figure 5). Once you have entered as much information as you can, click Save.
Figure 5. Regression tests, Add regression test project
Scenario Test builder
The Scenario test builder (Figure 6Test Builder.
Scenario Test Builder
The Scenario Test Builder (Figure 5) allows you to create a folder that will contain all the regression test files for a project. Use this tool as follows:
- Before running a scenario, ensure that you
- are recording the parameters relevant to your test
- Configure and run your scenario
- Ensure that all the recorded results are
- giving you the expected answer
- Repeat steps 1–3 for any additional scenarios that you wish to test
- Open the Scenario Test Builder
- using Tools » Regression Tests » Scenario Test Builder
- Click on the ellipsis button
-
and navigate to the folder where you want to save your baseline data and project for the regression test. Click Save to save the folder location or Clear to load a different folder.
- Once you save, Source will create a sub-folder with the name of your project which contains:
- Sub-folders for each scenario within your project
containing the expected results or baseline files. This folder also contains a - called S01, S02, ... etc. Each of these folders contain *.csv files, which are the recorded results for that scenario. These are the baseline files for your regression test, that is, your expected results.
- A Source project file that the
regression test - Test Runner loads and runs to compare to the baseline files.
- Test Runner loads and runs to compare to the baseline files.
| Info | ||
|---|---|---|
| ||
Note: To load a project with plugins, the folder containing the Source project must also contain a file listing all the plugins used in the project. Source generates a 'Plugins.csv' file in the output folder when all the plugins are loaded. This file contains the required plugins and their location when running a regression test. |
Figure
65. Regression tests, Scenario Test builder
Create/Edit Regression Test Description file (.xml)
This allows you to document information about the test files that were saved in the scenario test builder. It tells you what functionality each file is testing and is saved in XML format.
Choose Tools » Regression Tests » Create/Edit Regression Test Description file (.xml) to open the Add Regression Test Project dialog (Figure 6). Once you have entered as much information as you can, click Save.
Figure 6. Regression tests, Add regression test project
Test Runner
The test runner allows you to run various tests on scenarios:
- Choose Tools » Regression tests » Test Runner to open the dialog shown in Figure 7;
- Click on the ellipsis button to load a folder containing the errors; and
- Click Run to run the scenario.
By default, a fast regression test is run. This loads, runs, saves and then compares the result to XXX. Ticking Run slow regression test repeats the fast regression test a second time, so additionally tests whether Source can save and reopen the scenario, and also confirms the run results are consistent.
Click the Hide Info. button to view fewer details on the errors. The Export All Errors button allows you to save the errors to a file.
Figure 7. Regression tests, Test Runner