Irrigator operates on a daily basis generating demands and extracting water to meet these demands via the water user and supply nodes. Irrigator maintains a daily water balance for each cropping area during its planting season, to calculate the daily soil water deficit and an irrigation requirement. The irrigation requirements are used by the Water User to generate orders and opportunistic requests and to subsequently place orders and requests and to extract water from a water source.The model can be applied in both regulated and unregulated systems.
Configuring generic crop settings
The Irrigator model is based on FAO56 - "Crop evapotranspiration - Guidelines for computing crop water requirements - FAO Irrigation and drainage paper 56: (http://www.fao.org/docrep/X0490E/X0490E00.htm). Before configuring an Irrigator Demand Model on a Water User node, you must specify crop factors for the entire scenario using Crop factors defined in this way are accessible for each water user node. More details regarding this can be found under at IQQM CropMod2 Demand Model(insert link here).
To configure an irrigator demand model in Source, right click Demand Models in the Water User node's feature editor and choose Add Irrigator (Figure 1).
District Configuration
This describes a number of parameters that can be set at an irrigation district level. The maximum irrigated area is a nominal following parameters must be configured:
- Maximum irrigated area - this represents the maximum area that can be
...
- irrigated within a
...
- district. It is used to calculate the fallow area at each time-step, which impacts on the rainfall runoff from the fallow area. The total irrigated area can exceed the maximum irrigated area if incorrectly configured, causing a warning message to be recorded at run time;
- Soil moisture capacity - this is assumed constant for all crops in the district.
...
- Soil moisture capacity is nominally the difference between the soils field capacity and permanent wilting point; and
- Irrigation start and end dates - if these are configured, orders and requests
...
- will only be generated within the irrigation season.
...
Feature Editor - Irrigator Demand Model (District Configuration)
Figure 1. Irrigator demand model
Target Modifier
Irrigation modifiers are included in Source to allow a simple mechanism to reduce irrigation intensity for recurring time periods. To enable a target modifier, right click on the demand model and choose Add Target Modifier (as shown in Figure 1). This provides equivalent functionality to demand reductions in the PRIDE model. By specifying a target modifier, a new soil depletion target is calculated during the specified period that results in a reduction in irrigation demand equivalent to the modifier you specified.
District Supply Escape
The district requirement is adjusted to allow for any district delivery supply escapes and losses associated with delivering water to the district. The volume removed removed before getting to the crop is is called the escape volume. The escape volume can either be lost from the system or returned back to the water user as a return flow. This is an optional parameter in the demand model configuration and can be added by right clicking the Irrigator (menu item) and selecting clicking Irrigator, then choosing Supply Escape. It is expressed as a percentage.
Screenshot needed?
District Return Efficiency
Returned water is surplus drainage water from irrigation or from rainfall runoff. This water can be redirected into the on farm storage or otherwise can be returned to the river via a confluence node. This is optional in the demand model configuration and can be added by right clicking the Irrigator (menu item) and selecting and choosing Add Return Efficiency. It This is also expressed as a percentage
Target Modifier
Irrigation modifiers are included into Source to allow a simple mechanism to reduce irrigation intensity for recurring periods of time.
Climate Configuration
There are four parameters that can be defined for climatic data
Feature Editor - Irrigator Demand Model (Climatic Parameters)
Crop Configuration
This is used to define parameters specifically related to the crop to be planted. Add a new crop by right clicking Irrigator and selecting Add Crop Type. The Source Scientific Reference Guide should be consulted for greater detail regarding parameters for the following sections.
Feature Editor - Irrigator (General Crop Configuration and Soil Configuration)
:
- Evapotranspiration - defined in FAO56 as the amount of transpiration that would occur from a reference crop. Procedures for calculating evapotranspiration are documented in FAO56. In addition, the BOM and SILO climate products produce daily estimates for FAO56. Alternatively, pan evapotranspiration and pan factors can be used to define evapotranspiration;
- Average evapotranspiration (Figure 3) - used when forecasting orders. These options are provided for specifying the average evapotranspiration. You can enter a daily pattern of average evapotranspiration, specify an expression, or you can select to calculate an average evapotranspiration runtime, where the average is calculated as a rolling average of the number of previous model time-steps specified. A value of 14 days would be a good first estimate; and
- Rainfall and average rainfall are used to specify the actual forecast rainfall. The former can be specified as a constant value, a time series or a function (as shown in Figure 4). The latter is similar to Figure 3.
Figure 2. Irrigator demand model (Climatic parameters)
Figure 3. Irrigator demand model (Average evapotranspiration)
Figure 4. Irrigator demand model (Rainfall)
Fallow Crop
Areas that are not being cropped are referred to as fallow. Every irrigator demand model has, by default, one fallow area. Fallow area occurs between cropping seasons or during the irrigation season if the maximum developed area is not planted. The fallow cropping area does not order or receive irrigation water. Although the However, a soil water balance of the fallow crop is maintained, and impacts on rainfall runoff from the fallow area and the initial souild moisture assigned to new crops area. The depth of rootzone is also specified for fallow , the fallow has no rootzone. This is treated as the represents the depth of soil from which evaporation can occur.
Crop Configuration
This is used to define parameters specifically related to the crop to be planted. To add a new crop, right click Irrigator and choose Add Crop Type. Figure 5 shows an example of a crop, named Wheat, that has been added to the model. Consult the Source Scientific Reference Guide for greater detail regarding parameters for the following sections.
Figure 5. Irrigator demand model (General and Soil Configurations)
Soil Configuration
Crop specific soil factors can be defined on the same page as General Configuration see Feature Editor - Irrigator (General Crop Configuration and Soil Configuration)- see Figure 5. Soil moisture capacity is specified at the district level and this is assumed constant for all crops in the district. The Depth of the Root Zone, Depletion Factor and Initial Depletion are specified for each crop.
...
Planting decisions are represented as a trigger in the Irrigator Demand Model using includes and include a decision type, plant date, optional harvest date , planted area definition and an under irrigation factor.The number and size of cropped areas changes over time in response to planting decision triggers and available water.
| Info | ||
|---|---|---|
| ||
| Note: Irrigator allows more flexible representations of crop based planting decisions than earlier crop demand models, which better align with economic modelling |
...
| . If the planted area is defined using the |
...
| Function Editor, then other factors such as economics can be considered. In addition, planting decisions can be reviewed periodically during the season. This allows decisions to be made to cut back the irrigated area, reduce irrigation intensity or potentially trade water if there is insufficient water to finish the crop. |
Feature Editor - Irrigator (Planting Decision Trigger)
...
Figure 6. Irrigator demand model (Planting Decision, Fixed Area)
If Lookup Table is choosen as the Decision Type, you must define a configuration table (as shown in Figure 7), which can be entered manually or imported using the Import button. This table is used to determine the Area and Underirrigation Factor for a given value of Available Water. Additionally, for values of Available Water that are not present in the table, linear interpolation is used to determine the other two parameters. For the example shown in Figure 7, if available resources in a RAS are 15000ML, the planting area will be 3000ML based on linear interpolation between (10000, 2000) and (20000, 4000). The available resources from water user (order debit type) is determined from the current account balances plus released water in the river plus on farm storage available water.
Figure 7. Irrigation demand model (Planting Decision, Lookup Table)
Target soil depletion
The amount of water in the rootzone is defined in terms of rootzone depletion. Rootzone depletion , which describes the soil water deficit of the rootzone , relative to field capacity. The target depletion is a user specified input and can be specified as either a time series, a pattern or as an expression.
Two target depletions can be specified 1) (as shown in Figure 6):
- A Regulated Target
...
- - the target at which Irrigators water and attempts to maintain soil depletion
...
- ; or
...
- An Opportunistic Target
...
- - used to generate opportunistic requests.
Economics
Need more information on how Economics works. Seem to only have 2 used parameters in SRG and no explanation
Feature Editor - Irrigator (Crop Economics)
Crop Runoff
This is to specify the proportion You can configure some simple economic considerations in Irrigator, as shown in Figure 8. To enable economic values to be configured for a crop, right click on the crop and choose Enable Economics. A simple, linear crop water production function is used to predict the reduction in crop yield resulting from water stress. Irrigator records the relative yield as a daily time series. The following parameters must be specified as an expression:
- Yield factor - represents the Yield response factor, as expressed in equation 90 of FAO56. This parameter defines how yield is reduced as a result of water stress. It is used in the calculation of the relative yield daily time series (one of the outputs of the demand model). Note that in Irrigation, the yield response factor is entered as a percentage rather than as a fraction;
- Expected Usage - this is a depth measured in mm (note that 100mm is equivalent to 1ML/ha); and
- Productivity - allows you to multiply the relative yield by a productivity term (eg. $/ha or tonnes/ha) to calculate socio-economic outputs.
For more information consult the Irrigator Demand Model page of the Source Scientific Reference Guide.
Figure 8 - Irrigation demand model (Crop Economics)
Runoff
The supply escape efficiency defines the amount of applied irrigation water that becomes runoff, as well as the runoff that can be harvested and returned. A value of 0 results in no irrigation runoff; 10% indicates that 10% of the applied irrigation water becomes runoff. You must also specify a return efficiency, which means that the proportion of runoff that is returned to the water user can be stored in the farm storage or returned to the river. By default, both are set to 0 and do not need to be configured.
Crop Deep Percolation
This is to specify specifies the percentage of applied irrigation and rainfall that becomes deep percolation and drains below the rootzone. . A 10% supply escape efficiency would indicate that 10% of the applied water becomes runoff. The return efficiency is not configurable for deep percolation.