Introduction

A Source scenario must be run in order to produce any useful information. Each scenario run produces a collection of result sets. A result set is a group of related outputs, usually from the same component and is usually, but not always, arranged as a time series.

During a run, each component in the scenario can produce one or more result sets in the form of predicted water flows, volumes and other outputs specific to that component. Some components are capable of producing more than 20 separate result sets. When ownership is not enabled, the model starts at the first node then progresses down the river system in a single pass to compute the water volume and flow rates through each node and link.

Recording parameters

When you run a scenario, every node and link produce results in the form of predicted water flows, volumes and other data outputs. To view or save these model outputs after the run, you need to select them to record before you run. When you save a project or make a copy of a scenario, Source automatically saves the list of model outputs selected for recording. There are two ways to select which parameters and model elements to record, using the Project Hierarchy to select model parameters at the component level (eg. links, nodes), or more fine-grained parameter-level control in the Parameter pane.

Performance Improvement

Before running the scenario, give consideration to the required output and only record the parameters of interest. Some node or link types can produce more than 20 separate data outputs (eg. storages). In general, the more outputs you record, the longer the simulation will take, though this depends on exactly what you record; recording mass balance is more computationally intensive than recording inflow, for example

Component-level controls

For a given scenario run, you can select which outputs will be recorded using the component's contextual menu or the Record icon in the Project Explorer toolbar:

Using the Project Explorer, right-click a group or individual model element (eg. node, link, function or other element) in the Project Hierarchy (Figure 6). From the contextual menu, select:

Record All – every parameter at this level and below will be recorded;
Record None – no parameters at this level and below will be recorded;
If the indicator appears as , some (not all) parameters at this level and below will be recorded.

If you select a component on the Geographic Editor or Schematic Editor (eg a catchment outlet), then the chosen component is highlighted in the Project Hierarchy. Right-click the component's name and select the recording status from the contextual menu, or click the Record icon in the Project Explorer toolbar.

Note: Model elements that are not nodes or links are grouped under Miscellaneous. For example, you can record functions and data sources here.

Figure 6. Selecting recording parameters

Parameter-level controls

For fine-grained control of individual recordable parameters (Figure 7):

Select the group or model element within the Project Hierarchy. Selection causes all of the group's or element’s parameters to be displayed in the Parameters area; and
Use the contextual menu to enable or disable individual parameters or parameter groups.

Figure 7. Selecting model parameters

Note: The contextual menus shown in Figures 6 and 7 can be applied at any point within their respective hierarchical displays. If you select an individual model element, the effect will be limited to just that element. Applying a recording choice to a group propagates the effect to all elements grouped below it in the hierarchy. For example, to record only Downstream Flow for all straight-through routing links, you would select Link » Straight-Through Routing and choose Record None (Figure 6), and then select Downstream Flow in the Parameter pane and select Record All (Figure 7).

Using the Log Reporter

If a scenario run results in errors or warnings, the first indication of those is displayed in the Run completion dialogue by a red or yellow icon next to the Close button as indicated in Figure 7.

Figure 7. Running scenario (error)

You can investigate the causes of errors or warnings using the Log reporter (Figure 8). If the Log Reporter window is not visible, do either or both of the following:

Choose View » Log Reporter to make it visible; and/or
Make the Log Reporter active by clicking the Log Reporter tab.

Once the Log Reporter is active, you can view all the logs run by Source, from configuring a scenario to running it. You can clear the log or export its contents to a .csv file using the contextual menu (as shown in Figure 8). Table 1 provides a description of each of the columns in the Log Reporter.

Figure 8. Log Reporter

Table 1. Log Reporter, Columns

Column	Description
Date	The local date on the computer.
Run	The run number. You can also filter messages based on this number - use the filtering icon.
Level	The /wiki/spaces/SD47/pages/54167215 associated with the message, which can be one of information, warning, error or fatal. The messages are classified according to the way in which they were generated (see Message Type).
Time Step	The scenario time-step which the message refers to.
Name	Name of the node or link corresponding to the message.
Model Type	These are the node and link types – ie. Inflow, Straight Through Routing
Message	Details of the message.
Message Type	There are three types available: Admin - These are general administration messages and are generally logged from non-runtime sources such as an inability to parse a function; Note - These are user-generated notes added throughout the system; and Run time - These are generated throughout the simulation run. Some of these are user-configurable /wiki/spaces/SD47/pages/54167215.

Execution order rules

During a scenario run, components of the scenario are run in a particular order to ensure that they comply with inbuilt Simulation phases and execution order rules.

Note: The execution order is based on leaf node names alphabetically. Thus, renaming a node can change the order.

Execution order rules are now available in Scenario Options: /wiki/spaces/SD47/pages/54165590

Scenario results

Note: Results of a scenario run can be viewed in the /wiki/spaces/SD47/pages/54165721 or using the /wiki/spaces/SD47/pages/54166688.

Once run, every scenario generates a result set – a distinct collection of results recorded for that run. Scenario results can be examined and analysed using the Results Manager, which opens when a run completes. Within Results Manager, results can be evaluated graphically in charts, numerically in tables or as statistics, and they can also be filtered and manipulated using transforms. With /wiki/spaces/SD47/pages/54165721, you can also view and statistically analyse multiple results within and between runs, compare results to external data sources and automatically update with the latest results each time a model is run. See/wiki/spaces/SD47/pages/54165721 for more information.

In Results Manager, result sets are listed in the tree menu on the left side. The name of scenario's result set is formed by concatenating the run number from the current session with the name of the scenario. If there are errors or warnings from your run, these are indicated by an appropriate symbol next to the result set's name (see /wiki/spaces/SD47/pages/54167215), and are also listed in the Log Reporter (see Using the Log Reporter). For example, Figure 11 shows that in this Source session, Stage C was run first, and had warning(s) associated with it, Stage B was run next and had a fatal error that stopped the run from completing, and Stage A was run third without any warnings or errors.

Figure 11. Results Manager

Identifying constraints

When constraints are enforced, there may be a difference between the amount of water ordered and that released. The application of constraints is evident at both the supply point and minimum flow requirement nodes.

To discover where constraints have been applied:

Run the model;
Select an appropriate supply point or minimum flow requirement node. This selects all of the node’s recording parameters in the Recording Manager; and
Inspect the Values column in the Recording Manager and click an Order Details link. This opens a Complex Time Series Form (Figure 12). The Graph tab provides a summary of the differences between the amount ordered and the amount released for the duration of the run. The Constraints column of the Table tab (Figure 13) provides a breakdown per time-step. Hover your mouse cursor over a cell of interest to see its contents presented in a tool tip.

Figure 12. Complex time series (Orders vs Releases, summary)

Figure 13. Complex time series (Orders vs Releases, detail)

Browser not supported