Introduction

Water ownership deals with the assignment and tracking of water as it is stored in, transits through, and exits river systems. This is an important aspect of water management, as it allows resource sharing amongst owners with the ability to determine how much water an owner has, and where it is located.

Ownership is a combination of the following three systems in Source:

Ordering - processes orders received from water users;
Resource Assessment - allocates owners’ water to individual account holders; and
Distribution, borrow and payback - handles water transfers from owners that have a surplus to those that have a deficit.

They communicate with each other via an ownership system, which is created by default when ownership is enabled.

Note: Within an ownership system, ownership of water is conserved unless it is explicitly transferred. This applies to both nodes and links.

Ownership in Source

Ownership must be enabled individually for each scenario. Once a scenario has been created, enable ownership as follows:

Choose Edit » Ownership... to open the Ownership Setup dialog (Figure 1); and
Right-click on the scenario and choose Enable Ownership.

Figure 1. Ownership setup dialog

When ownership is initially enabled in Source, a single ownership system is created by default, comprising of the following elements:

A single owner (Owner 1);
A default distribution system with a single priority level;
A global borrow and payback system; and
All links and nodes in the scenario that fall within the boundary of the ownership system.

To disable an existing ownership system, choose Disable Ownership.

Note: Once an ownership system has been created, it cannot be deleted.

Boundaries

All nodes must fall within the boundaries of an ownership system (of which there can be multiple). Within the boundaries of the ownership system, a defined set of owners operate and share water as required. Boundary nodes are those that form the boundaries of an ownership system. These are either the top-most nodes in the network (such as an inflow node), scenario transfer nodes, or transfer ownership nodes. When ownership is first enabled, the entire modelling scenario falls within the boundary of the default ownership system and every node and link belongs to this system.

Figure 2 shows the boundary nodes of the ownership systems in the model. You can specify which node forms the boundary of an ownership system using the drop-down menu. Overlap of ownership system boundaries may occur as a result of nodes being added to or removed from the model network, which can be corrected in the Ownership Setup dialog.

Note: An owner cannot exist across two ownership boundaries.

Figure 2. Ownership boundaries

Ownership systems

An ownership system allows a defined set of owners to share water in a chosen section of the river network. A scenario may have multiple ownership systems and is made up of several network elements (Figure 3). It has a set of owners that share water within the system’s boundaries, where each of these owners lend water surplus to other owners with a deficit via the borrow and payback systems. Lending owners can be paid back later at a nominated storage or implicitly through the resource assessment process. It also shows the link sharing rules that are applied throughout the ownership system. Murray style losses indicate whether Murray style high flow losses will apply on links with flow above a configured threshold. Additionally, you must also specify whether other types of fluxes (Time series, Lateral and Operational Excess) will be distributed as a fixed ratio or proportionally amongst owners in the ownership system.

Figure 3. Ownership, Ownership systems

Owners

When ownership is enabled, a river model consists of owners that have a share of the total available water (resource). There is one owner by default (named Owner 1) who initially owns 100% of the water in every node and link. To add additional owners in the system, click Owners, then add them in the table. Also specify the various proportions for each owner (Figure 4). In addition to the parameters listed, for each owner, their percentage of the various link’s parameters must be specified as well.

Figure 4. Ownership, Owners

Ordering and ownership

In Source, ordering deals with passing orders up the network whereas ownership handles these orders being distributed to owners (coming down the network). As owners request a share of the resource, orders travel upstream in the network and each node passes it up and might make changes to the order depending on the node’s characteristics, or its configuration. The ordering phase needs to consider the ownership of losses and gains such that when the order reaches a storage, the correct volume of each owners’ water is released. It also needs to consider ownership of maximum and minimum order constraints.

Note: In Source, ownership is based on rules-based ordering.

For demand models/water user, which owner orders the water depends on the distribution system used:

If you are using non-account based sharing then you specify the percentage of the order that you want to attribute to each owner;
If you are using account based sharing, then the ownership of the orders is determined by the ownership of the accounting system used.

Resource assessment and ownership

Owners may have one or more resource assessment systems managing their water. This system must be explicitly created and configured via the Resource Assessment Explorer. Figure 5 shows the Resource Assessment Explorer (left side) indicating the ownership systems that are available. The Ownership dialog (right side) shows the resource assessment systems for which ownership has been activated. Resource assessment systems may also be used to pay back water that has been borrowed amongst owners. For configuration details on this, refer to Borrow and payback with resource assessment.

Note: You can have only one ownership system in a resource assessment system.

Figure 5. Ownership and Resource Assessment Systems

Ownership at nodes and links

Source automatically assigns each node and link to an ownership system when boundaries, resource assessment systems and owners are added to a modelling scenario. Source undertakes a check for ownership system consistency for the entire river network, examining every node and link. The rules of ownership consistency are as follows:

For a Transfer of ownership node, the upstream ownership system must match the inlet link’s ownership system and the downstream ownership system must match the outlet link’s ownership system;
A water user node can have multiple ownership systems that are connected at different supply point nodes; and
For all other nodes, the upstream link’s ownership system must match the current node’s ownership system. For every connected downstream link, the downstream link’s ownership system must match the current node’s ownership system.

At every node in the network where an inconsistency is found (such as overlap of ownership systems at a node), an error appears in the Ownership Setup dialog showing details of the discrepancy. An example of this is shown in Figure 6.

Figure 6. Ownership, error

Once you have enabled ownership, you can configure it at each node by choosing Ownership in their respective feature editors. Alternatively, choose the relevant node under Nodes in the Ownership Setup dialog. Refer to Ownership at nodes and links for configuration options at each node and link. In most feature editors, the following information is required at each node and link:

Each owner’s share of initial volume/flow of water at the node or link;
Each owner’s share of fixed fluxes at each time-step, that are to be shared in a predetermined way (other fluxes will be ‘proportional’, ie. shared in proportion to the owner’s existing share of water at the link or node); and
In most nodes (explained next), you can specify the sharing method using either a fixed ratio (this is a ratio of the total for all owners) or a proportion (as a function).

Note: When shares are allocated to multiple owners in a system in Source, they are effectively unit shares, ie. they are scaled to add up to 100%.

Suspension of ownership

Ownership can be temporarily suspended at storages where you have specified an override owner, resulting in the model operating as one where ownership has been disabled.

The result of suspending ownership is:

All water at a storage is assigned to a single owner; and
All borrow and payback ceases.

Note: When ownership is enabled once again, the system is restored to the state it was in before ownership was suspended.

The 640/480 rule applied at the Menindee Lakes (located on the lower Darling River in NSW) is an example of a situation where ownership is suspended temporarily (between the owners NSW and Victoria). It operates as follows:

If the storage volume falls below 480GL, NSW is given full ownership;
If the storage volume is between 480GL and 640GL, ownership is shared if the volume is rising. However, if it is falling, NSW is given full ownership; or
If the storage volume rises above 640GL, ownership is shared between NSW and Victoria.

Interpreting results

To understand how ownership has operated in a model, you must observe its effects on each of the three systems that make up ownership. Enable the following parameters for recording (under Model Parameters):

Ordering - you can view all order-related data for each node;
Ownership; and
Resource Assessment

Browser not supported